want to buy nanoglass cutting blade discs ? we have special nanoglass cutting blade disc for the nano glass, nano stone, nano crystallized glass panel. you can buy the nanoglass stone tool from xiamen tianrun stoneglass at chinamarmoglass.com

#nanoglassblade #nanoglassdisc #cutnanoglass #howtocutnanoglass #nanoglasscutting #nanoglasstool #nanoglasstabletop #nanoglasscountertop #crystallizedstoneslabs

Nanoglass cutting blade

blade diameter 4" is 7 usd each piece;

blade diameter 14" is 45 usd each piece;

blade diameter 16" is 55 usd each piece;

CUTTING FOR MARMOGLASS and NANOGLASS

1、Use equipment with excellent mechanic performances, sharpness of the saw bit is the best, the thickness of saw bit is between 2.4MM -2.6MM . Grind the thickness of the blade to the best with firebrick before every cutting, the grinding time should not less than fifteen minute. Diameter of the sow bit should between Φ 350mm -Φ 400mm (Imported saw bit is preferable)

2、 Mind the cutting traveling speed while cutting the sheet material; usually the cutting speed is 2.5m /mim -5m /mim. Reduce the speed when move in or out the blade so the stone will not be broken. Speed of the main blade when bridging cutting is about 2500r/min. The higher the rotary speed, the cutting result is better.

3、 Be careful when processing project plate lower than 1000mm . The flatness the worktable should be very high. If the worktable is not flat enough, the corners is easy to fall off when cutting.

4、 Separate the cut plates with pearl cotton, because it is fragile.

5、 Project plates need edge grinding, chamfer processing. Glass straight beveling machine can be used, mind the force of every grinding head while grinding on the beveling machine, power quantity of every diamond grinding wheel should not excess 1mm , main belt of the beveling machine should be parallel with the plate feeding belt, or the plate would be uneven. When side angle need polishing, resin grinding wheel can be used. If this equipment is not available, portable hydrostone-flat grinder can also be used.

6、 Use Φ35 glass drill head when processing alien plate, mark the outside wire of tapping. And then use special stone drill head to drill several small holes around the hole. Drill holes in the four corners when drilling a square hole. Cooling water should be used, and the cutting blade should also be grinded in firebrick before operation. Be careful when operating, it should be slashed at one time, it should be slashed for several times, and cooling water should be used in slashing to prevent broking.

7、 While grinding the curved edge, first mark the lines, prepare the shape with hand grinding machine and then polish with portable hydrostone-flat grinder. The operation method is similar with other stone edge-grinding method. What should mind is that it can not be grinded when it is dry, water is needed when polishing. When thicken an edge, grind the edge roughly with grinding machine, the same as the added slips. Then clean the roughly grinded parts, if there is dust or other things, the adhesive force would be interfered. When making a France edge, first scratch the line with cutting machine and then grind the edge with the same method. So the best effect might be achieved.

8、 When cutting a 45-degree angle, regulate the gradient of the main blade to the best with hand power cutting machine, and then clean the worktable, regulate the fixing plate. It is a good put a rubber plate on the worktable. So the surface of the plate would not be scratched. Grind the saw bit before processing, and check the water quantity, the speed should not be too high.

9、 Process the stair footplate, antislip slot and the plate whose edge should be slotted. Footplate of some projects should be thickened, the sixth and seventh method can be used. Special mind should paid on alien plate edge, when cut the stair footplate for the second time, verso plate cutting should be processed. And open a antislip slot and plate edge slot, requirement of the customers should be considered. When open the slot again with hand power to regulate the slotting width. Use the saw bit according to the slotting width. Thickness of the saw bit is 2.4, generally two saw bit would be installed on the workplate for slotting. Add the sea bit according to the size of processing. Slotted edge should be shine, grind with portable hydrostone-flat grinder.

10、 Process steel hanged plate edge, fixed plate should be used on the workplate of hand power edge cutting machine. Fix the plate vertically and then regulate the workplate, add or subtract saw bits according to the width of slots.

11、 Be careful when piling processed finished plates, pile the finished plates in cubes. Do not pile too many in one place to prevent broken.

https://www.instagram.com/p/C0t4GIMLsRC/